Titan Impact 1140

The unit will not run. The unit will not prime. The unit will not build or maintain pressure. Fluid leakage at the upper end of the fluid section. Excessive surge at the spray gun. Poor spray pattern. The unit lacks power.

From 2421887 rev H, page 12

The Communication Error screen appears when the Xact Digital Control System loses COMMUNICATION ERROR communication with the control panel. Take the sprayer to a Titan authorized service center for repair.

From Titan 1140 ix Digital Owner's Manual, page 15

1. Spray tip is worn Replace the spray tip

From 805-915 rev Z, page 9

1. Fluid section wear (worn packings, worn piston, stuck valve, etc.) when using a new tip and pressure is set at maximum Service may be required

From 805-915 rev Z, page 9

1. Paint buildup in the tip Lock gun trigger, shut pump off, and release all pressure before servicing, cleaning tip or guard, or changing tip
2. Debris or dried paint in the nozzle tip Lock gun trigger, shut pump off, and release all pressure before servicing, cleaning tip or guard, or changing tip using the Pressure Relief Procedure

From 805-915 rev Z, page 4

1. Pressure setting too low Increase
2. Electric motor burned out Replace
3. Switch defective Replace
4. Circuit breaker on sprayer tripped Reset the breaker

From Titan 1140 ix Digital Owner's Manual

1. Air in line Check siphon tube o-ring and/or let paint circulate in prime position
2. Insufficient pressure Increase pressure
3. No paint Check supply
4. Siphon strainer clogged Clean
5. Sprayer/gun filter clogged Clean & replace
6. Sprayer will not prime, material too heavy Thin material

From Titan 1140 ix Digital Owner's Manual

1. Air leak in system Tighten connections
2. Air leak in siphon tube Tighten, check for leaks
3. Inlet valve not seating Service or clean
4. Worn packings Replace
5. Dirty or worn ball valves Clean or replace
6. Worn valve seats Reverse
7. Worn prime valve Replace

From Titan 1140 ix Digital Owner's Manual

1. Pressure setting too low Increase
2. Plugged filters Clean or replace
3. Spray tip too big or worn Change or replace
4. Wrong type of hose Replace with a minimum 50' grounded nylon braid high pressure hose

From Titan 1140 ix Digital Owner's Manual

1. Spray tip too big or worn Change or replace
2. Excessive pressure Decrease pressure and engine speed

From Titan 1140 ix Digital Owner's Manual

1. Air in system Inspect connections for air leaks
2. Dirty gun Disassemble and clean
3. Needle assembly out of adjustment Inspect and adjust

From Titan 1140 ix Digital Owner's Manual

1. Needle assembly out of adjustment Inspect and adjust
2. Broken or chipped seat Inspect and replace
3. Worn or broken needle & seat Replace

From Titan 1140 ix Digital Owner's Manual

1. Worn or broken needle & seat Replace
2. Needle assembly out of adjustment Adjust
3. Dirty gun Clean

From Titan 1140 ix Digital Owner's Manual

1. Needle assembly out of adjustment Adjust
2. Dirty gun Clean
3. No paint Check fluid supply
4. Plugged filter or tip Clean
5. Broken needle in gun Replace

From 2421887 rev H

1. Inadequate fluid delivery Increase pressure
2. Fluid not atomizing Change to smaller tip

From Titan 1140 ix Digital Owner's Manual

1. Insufficient velocity Clean gun and pump filters
2. Material too cohesive Reduce viscosity

From Titan 1140 ix Digital Owner's Manual

1. Tip worn past sprayer capacity Replace
2. Worn tip Replace
3. Tip may be chipped Replace

From Titan 1140 ix Digital Owner's Manual

1. Plugged, worn or chipped tip Clean or replace
2. Leak in suction tube Tighten
3. Not enough hose Use a minimum of 50' (15m) of 1/4" high pressure hose
4. Tip too large or worn Replace with a new or smaller tip

From Titan 1140 ix Digital Owner's Manual

1. The unit is not plugged in Plug the unit in
2. Tripped breaker Reset the breaker
3. The pressure is set too low (pressure control knob set at minimum setting does not supply power to unit) Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting
4. Faulty or loose wiring Inspect or take to a Titan authorized service center
5. Excessive motor temperature Allow motor to cool
6. ON/OFF switch is defective Replace the ON/OFF switch

From Titan 1140 ix Digital Owner's Manual

1. The PRIME/SPRAY valve is in the SPRAY position Rotate the PRIME/SPRAY valve clockwise to the PRIME position
2. Air leak in the siphon tube/siphon assembly Check the siphon tube/siphon assembly connection and tighten or re-tape the connection with PTFE tape
3. The pump filter and/or inlet screen is clogged Remove the pump filter element and clean. Remove the inlet screen and clean
4. The siphon tube/siphon assembly is clogged Remove the siphon tube/siphon assembly and clean

From Titan 1140 ix Digital Owner's Manual

1. The spray tip is worn Replace the spray tip following the instructions that came with the spray gun
2. The spray tip is too large Replace the spray tip with a tip that has a smaller orifice following the instructions that came with the spray gun
3. The pressure control knob is not set properly Turn the pressure control knob clockwise to increase the pressure setting

From Titan 1140 ix Digital Owner's Manual

1. Material flows from the return hose when the PRIME/SPRAY valve is in the SPRAY position Clean or replace the PRIME/SPRAY valve
2. Air leak in the siphon tube/siphon assembly Check the siphon tube/siphon assembly connection and tighten or re-tape the connection with PTFE tape

From Titan 1140 ix Digital Owner's Manual

1. There is an internal fluid section leak (packings are worn and/or dirty, valve balls are worn) Clean the valves and service the fluid section following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual
2. Worn valve seats Reverse or replace the valve seats following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual

From Titan 1140 ix Digital Owner's Manual

1. The upper packings are worn Repack the pump following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual
2. The piston rod is worn Replace the piston rod following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual

From Titan 1140 ix Digital Owner's Manual

1. Wrong type of airless spray hose Replace hose with a minimum of 50' of 1/4' grounded textile braid airless paint spray hose
2. The spray tip worn or too large Replace the spray tip following the instructions that came with the spray gun
3. Excessive pressure Rotate the pressure control knob counterclockwise to decrease spray pressure

From Titan 1140 ix Digital Owner's Manual

1. The spray tip is too large for the material being used Replace the spray tip with a new or smaller spray tip following the instructions that came with the spray gun
2. Incorrect pressure setting Rotate the pressure control knob to adjust the pressure for a proper spray pattern

From Titan 1140 ix Digital Owner's Manual

1. The material being sprayed is too viscous Add solvent to the material according to the manufacturer's recommendations

From Titan 1140 ix Digital Owner's Manual

1. The pressure adjustment is too low Rotate the pressure control knob clockwise to increase the pressure setting

From Titan 1140 ix Digital Owner's Manual

1. Improper voltage supply Reconnect the input voltage for 120V AC

From Titan 1140 ix Digital Owner's Manual

1. Spray tip is worn Replace the spray tip
2. Sprayer is in need of service/repair Service or repair the sprayer

From Titan 1140 ix Digital Owner's Manual

1. The unit is not plugged in. Plug the unit in.
2. Tripped breaker. Reset the breaker.
3. The pressure is set too low (pressure control knob set at minimum setting does not supply power to unit). Turn the pressure control knob clockwise to supply power to the unit and increase the pressure setting.
4. Faulty or loose wiring. Inspect or take to a Titan authorized service center.
5. Excessive motor temperature. Allow motor to cool.
6. ON/OFF switch is defective. Replace the ON/OFF switch.

From 2421887 rev H, page 12

1. Inlet valve is stuck. Insert pusher stem.
2. The PRIME/SPRAY valve is in the SPRAY position. Rotate the PRIME/SPRAY valve clockwise to the PRIME position.
3. Air leak in the siphon tube/suction set. Check the siphon tube/suction set connection and tighten or re-tape the connection with PTFE tape.
4. The pump filter and/or inlet screen is clogged. Remove the pump filter element and clean. Remove the inlet screen and clean.
5. The siphon tube/suction set is clogged. Remove the siphon tube/suction set and clean.

From 2421887 rev H, page 12

1. The spray tip is worn. Replace the spray tip following the instructions that came with the spray gun.
2. The spray tip is too large. Replace the spray tip with a tip that has a smaller orifice following the instructions that came with the spray gun.
3. The pressure control knob is not set properly. Turn the pressure control knob clockwise to increase the pressure setting.
4. The pump filter, gun filter, or inlet screen is clogged. Remove the pump filter element and clean. Remove the gun filter and clean. Remove the inlet screen and clean.
5. Material flows from the return hose when the PRIME/SPRAY valve is in the SPRAY position. Clean or replace the PRIME/SPRAY valve.
6. Air leak in the siphon tube/suction set. Check the siphon tube/suction set connection and tighten or re-tape the connection with PTFE tape.
7. There is external fluid leak. Check for external leaks at all connections. Tighten connections, if necessary.
8. There is an internal fluid section leak (packings are worn and/or dirty, valve balls are worn). Clean the valves and service the fluid section following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
9. Worn valve seats Reverse or replace the valve seats following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
10. Motor powers but fails to rotate Take unit to a Titan authorized service center.

From 2421887 rev H, page 12

1. The upper packing is worn. Repack the pump following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
2. The piston rod is worn. Replace the piston rod following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.

From 2421887 rev H, page 12

1. Wrong type of airless spray hose. Replace hose with a minimum of 50' of 1/4" grounded textile braid airless paint spray hose.
2. The spray tip worn or too large. Replace the spray tip following the instructions that came with the spray gun.
3. Excessive pressure. Rotate the pressure control knob counterclockwise to decrease spray pressure.

From 2421887 rev H, page 12

1. The spray tip is too large for the material being used. Replace the spray tip with a new or smaller spray tip following the instructions that came with the spray gun.
2. Incorrect pressure setting. Rotate the pressure control knob to adjust the pressure for a proper spray pattern.
3. Insufficient fluid delivery. Clean all screens and filters.
4. The material being sprayed is too viscous. Add solvent to the material according to the manufacturer's recommendations.

From 2421887 rev H, page 12

1. The pressure adjustment is too low. Rotate the pressure control knob clockwise to increase the pressure setting.
2. Improper voltage supply. Reconnect the input voltage for 120V AC.

From 2421887 rev H, page 12

1. The upper packing is worn. Repack the pump following the 'Servicing the Fluid Section' procedure in the Maintenance section.
2. The piston rod is worn. Replace the piston rod following the 'Servicing the Fluid Section' procedure in the Maintenance section.

From 805-915 rev Z, page 14

1. The PRIME/SPRAY valve is in the SPRAY position. Rotate the PRIME/SPRAY valve clockwise to the PRIME position.
2. Air leak in the siphon tube/siphon assembly. Check the siphon tube/siphon assembly connection and tighten or re-tape the connection with PTFE tape.
3. The pump filter and/or inlet screen is clogged. Remove the pump filter element and clean. Remove the inlet screen and clean.
4. The siphon tube/siphon assembly is clogged. Remove the siphon tube/siphon assembly and clean.

From 805-915 rev Q, page 14

1. The upper packings are worn. Repack the pump following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
2. The piston rod is worn. Replace the piston rod following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.

From 805-915 rev Q, page 14

1. The spray tip is worn. Replace the spray tip following the instructions that came with the spray gun.
2. The spray tip is too large. Replace the spray tip with a tip that has a smaller orifice following the instructions that came with the spray gun.
3. The pressure control knob is not set properly. Turn the pressure control knob clockwise to increase the pressure setting.
4. The pump filter, gun filter, or inlet screen is clogged. Remove the pump filter element and clean. Remove the gun filter and clean. Remove the inlet screen and clean.
5. Material flows from the return hose when the PRIME/SPRAY valve is in the SPRAY position. Clean or replace the PRIME/SPRAY valve.
6. Air leak in the siphon tube/siphon assembly. Check the siphon tube/siphon assembly connection and tighten or re-tape the connection with PTFE tape.
7. There is external fluid leak. Check for external leaks at all connections. Tighten connections, if necessary.
8. There is an internal fluid section leak (packings are worn and/or dirty, valve balls are worn). Clean the valves and service the fluid section following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
9. Worn valve seats Reverse or replace the valve seats following the 'Servicing the Fluid Section' procedure in the Maintenance section of this manual.
10. Motor powers but fails to rotate Take unit to a Titan authorized service center.

From Titan 1140 ix Digital Owner's Manual, page 14

1. Unit unplugged or circuit fuse blown Check
2. Pressure setting too low Increase
3. Electric motor burned out Replace
4. Switch defective Replace
5. Circuit breaker on sprayer tripped Reset the breaker

From Titan 1140 ix Digital Owner's Manual, page 12

1. Air in line Check siphon tube o-ring and/or let paint circulate in prime position
2. Insufficient pressure Increase pressure

From Titan 1140 ix Digital Owner's Manual, page 12

1. No paint Check supply
2. Siphon strainer clogged Clean
3. Sprayer/gun filter clogged Clean & replace
4. Sprayer will not prime, material too heavy Thin material

From Titan 1140 ix Digital Owner's Manual, page 12

1. Air leak in system Tighten connections
2. Air leak in siphon tube Tighten, check for leaks
3. Inlet valve not seating Service or clean
4. Worn packings Replace
5. Dirty or worn ball valves Clean or replace
6. Worn valve seats Reverse
7. Worn prime valve Replace

From Titan 1140 ix Digital Owner's Manual, page 12

1. Pressure setting too low Increase
2. Plugged filters Clean or replace
3. Spray tip too big or worn Change or replace

From Titan 1140 ix Digital Owner's Manual, page 12

1. Wrong type of hose Replace with a minimum 50' grounded nylon braid high pressure hose
2. Spray tip too big or worn Change or replace
3. Excessive pressure Decrease pressure and engine speed

From Titan 1140 ix Digital Owner's Manual, page 12

1. Worn out packings Replace

From Titan 1140 ix Digital Owner's Manual, page 12

1. Air in system Inspect connections for air leaks
2. Dirty gun Disassemble and clean
3. Needle assembly out of adjustment Inspect and adjust
4. Broken or chipped seat Inspect and replace

From Titan 1140 ix Digital Owner's Manual, page 12

1. Worn or broken needle & seat Replace
2. Needle assembly out of adjustment Adjust
3. Dirty gun Clean

From Titan 1140 ix Digital Owner's Manual, page 12

1. No paint Check fluid supply
2. Plugged filter or tip Clean
3. Broken needle in gun Replace

From Titan 1140 ix Digital Owner's Manual, page 12

1. Inadequate fluid delivery Increase pressure
2. Fluid not atomizing Change to smaller tip
3. Insufficient velocity Clean gun and pump filters
4. Material too cohesive Reduce viscosity
5. Tip worn past sprayer capacity Replace

From Titan 1140 ix Digital Owner's Manual, page 13

1. Worn tip Replace
2. Tip may be chipped Replace

From Titan 1140 ix Digital Owner's Manual, page 13

1. Plugged, worn or chipped tip Clean or replace

From Titan 1140 ix Digital Owner's Manual, page 13

1. Leak in suction tube Tighten
2. Not enough hose Use a minimum of 50' (15m) of 1/4" high pressure hose
3. Tip too large or worn Replace with a new or smaller tip

From Titan 1140 ix Digital Owner's Manual, page 13